电动车库门的安装 

Installation and editing of garage door

1、轨道的安装：根据门板的宽度和高度确定两轨道固定性的位置并用水平管测水平，再用M8×41㎜的方头螺钉固定。用卷尺测准水平轨与墙壁及两水平轨之间的间距，用水平尺测准水平轨的水平，然后用M6.4×14㎜的小帽螺丝和六角螺帽将水平轨连接件与水平轨和轨道固定性连接固定。用带眼角钢制成两个三角架，然后将其与水平轨的末端用M6.4×14㎜的小帽螺丝、螺帽连接，并用M8×70㎜的膨胀螺栓固定到天棚或墙壁上。

1, rail installation: according to the door width and height to determine the location of the two rail fixed and horizontal tube measuring level, square head screws fixed by M8 * 41 mm. Measure the spacing between the rail and the quasi horizontal walls and two horizontal rail with tape, the quasi horizontal rail with horizontal feet level, and then use the cap screws M6.4 * 14 mm and six corners of the nut to the horizontal rail connection and the level of rail and rail fixed fixed connection. With eyes made of steel two tripod, and then at the end of the horizontal rail for M6.4 * 14 mm cap screws, screw cap, and M8 * 70 mm expansion bolts fixed to the ceiling or wall.

2、扭簧的安装：将扭簧中心支架、尼龙胶圈、固定法兰、与门体重量相匹配的扭簧、锁紧法兰、绕线轮、轴承支架按顺序（分清左右侧）套在镀锌钢管上，并注意各零部件是否安装正确。用M8×41㎜的方头螺钉将扭簧中心支架固定到洞口上部中间位置的短木板上，并注意避开链盒的安装位置。用M8×40㎜的螺栓将扭簧中心支架、尼龙胶圈、固定法兰和扭簧连接，再将扭簧和锁紧法兰连接。然后将轴承支架的下端用M9.5×19㎜的大帽螺丝和螺帽与水平轨连接件连接固定，轴承支架的上端用M8×41㎜的方头螺钉固定到侧木框上。

2, the installation of torsion spring: the torsion spring, the nylon apron, the fixed flange and the weight of the door match the torsion spring, the locking flange, the coiling wheel and the bearing bracket in order (to distinguish the left and right sides) on the galvanized steel pipe, and pay attention to whether the components are installed correctly. Using the square head screws M8 * 41 mm will spring center bracket to the middle position of the upper part of the short board, and pay attention to installation position to avoid chain box. The torsion spring center bracket, nylon ring, fixed flange and a torsion spring connected by bolt M8 * 40 mm, then connect the torsion spring and locking flange. Then the lower end of the bearing bracket with M9.5 * 19 mm large cap screw and the nut and the horizontal rail connecting the fixed connecting piece, the upper bearing bracket with lag screws M8 * 41 mm fixed to the side of the wood frame.

3、门板的安装：将底密封条放到底门板的底部，并用M4×16㎜或M6.4×16㎜的自攻钉将其从背面固定到门板上。将底轮支架放到门板的两侧*近底密封条的位置，1＃折页分别放到门板顶部的左中右三个位置上（宽度低于10英尺，中间位置是一个；宽度在10英尺至14英尺，中间位置是二个；宽度在15英尺至18英尺，中间位置是三个），并分别用M6.4×16㎜的自攻钉固定。然后将滚轮涂上甘油穿入底轮支架和1＃折页中，将此门板放到立好的轨道里并使其水平。将2＃折页、3＃折页、（4＃折页）、顶轮支架按顺序分别固定到各块门板顶部的左右位置，各块门板中间位置的连接采用1＃折页。将各块门板按顺序放到已立好的轨道里，用M6.4×16㎜的自攻钉连接各折页与各门板，使各块门板组合成一体。

3, installation: the bottom door seal on the door at the bottom end, and by tapping M4 * 16 mm x 16 mm or M6.4 nail from the back fixed to the door panel. The bottom wheels on both sides of the door stent into the near bottom sealing strip position, 1 fold respectively on the top of the door panel of the left and right three position (width less than 10 feet, is a middle position; the width of 10 feet to 14 feet, the middle position is two; the width of 15 feet to 18 feet the middle position is three, respectively), and M6.4 * 16 mm with tapping screws. The roller is then coated with glycerin and penetrated into the bottom wheel support and the 1 fold page to put the door in the upright track and make it level. The 2 folding, 3 folding, 4 folding and top wheel brackets are fixed to the left and right positions at the top of each door panel in sequence. 1 points are used to connect the middle positions of each door panel. The door panel in order to have a good track, by tapping M6.4 * 16 mm screw connecting the folding and the door, the door panels are combined into a whole.